IndiaMain Nozzle 6c for Air Jet LoomComplete specifications

Just fill in the form below, click submit, you will get the price list, and we will contact you within one working day. Please also feel free to contact us via email or phone. (* is required).

  • MAKROLON 2805 and 2856 Product Information

    2021-8-16 · inlet air temperature should be 250°F (121°C) and inlet air dew point should be -20°F (-29°C) or lower. The hopper capacity should be sufficient to provide a minimum residence time of 4 hours. Additional information on drying procedures is available in the Bayer brochure General Drying Guide.

    Get Price
  • [Parts Information] Conversion Kits: AIR JET LOOM ...

    Because the main nozzle clamper softly clamps the weft at the inlet of the main nozzle, allowing constant jetting stoppage, breakage of the covering yarn is completely prevented. Also, the weft does not go out of the nozzle because of repulsion. The weft does not go out of the nozzle even when air flowing from the …

    Get Price
  • Product Data Sheet Metco 6P-II Series Thermospray

    2016-7-2 · Compressed air 0.85 m3/min at 4.5 bar 30 ft3/min at 65 psi Air requirements b Standard air cap 0.69 to 1 bar 10 to 15 psi Pinch air cap 0.35 bar 5 psi Cooling air cap a 0.69 to 1.38 bar 10 to 20 psi Air jet assembly a 3.5 to 6.2 bar 50 to 90 psi a Dependant on specific coating application, gun hardware and coating …

    Get Price
  • Visual experimental research on the effect of nozzle ...

    2016-8-1 · A visual experimental platform for R124–DMAC bubble absorption in a vertical tube absorber was designed and built for this research. The bubble behaviors, flow pattern characteristics and distributions are observed and the bubble absorption heights (BAHs) were measured when the two kinds of different structure nozzles (single-orifice or multi-orifice nozzle…

    Get Price
  • NOZZLE TESTS FOR SIMULATING HEAVY RAIN IN

    2011-5-14 · AFwAtL-TR-93-31 31 NOZZLE TESTS FOR SIMULATING HEAVY RAIN IN A WIND TUNNEL-.7ames K. LuersIra B. Fiscus University of Dayton 'a* Research Institute Dayton, Ohio 45469 Ott January 1984 Final 'Report for Period February 1983 to February 1984

    Get Price
  • (PDF) Sensitivity Analysis of Fuel Injection ...

    2019-1-30 · Figure 6c showed the variation of the injection rate and nozzle exit velocity with the injection pressure during the steady state period. The mass fl ow rate of the nozzle and the jet velocity at the

    Get Price
  • MAKROLON 2805 and 2856 Product Information

    2021-8-16 · inlet air temperature should be 250°F (121°C) and inlet air dew point should be -20°F (-29°C) or lower. The hopper capacity should be sufficient to provide a minimum residence time of 4 hours. Additional information on drying procedures is available in the Bayer brochure General Drying Guide.

    Get Price
  • [Parts Information] Conversion Kits: AIR JET LOOM ...

    Because the main nozzle clamper softly clamps the weft at the inlet of the main nozzle, allowing constant jetting stoppage, breakage of the covering yarn is completely prevented. Also, the weft does not go out of the nozzle because of repulsion. The weft does not go out of the nozzle even when air flowing from the …

    Get Price
  • Product Data Sheet Metco 6P-II Series Thermospray

    2016-7-2 · Compressed air 0.85 m3/min at 4.5 bar 30 ft3/min at 65 psi Air requirements b Standard air cap 0.69 to 1 bar 10 to 15 psi Pinch air cap 0.35 bar 5 psi Cooling air cap a 0.69 to 1.38 bar 10 to 20 psi Air jet assembly a 3.5 to 6.2 bar 50 to 90 psi a Dependant on specific coating application, gun hardware and coating …

    Get Price
  • Visual experimental research on the effect of nozzle ...

    2016-8-1 · A visual experimental platform for R124–DMAC bubble absorption in a vertical tube absorber was designed and built for this research. The bubble behaviors, flow pattern characteristics and distributions are observed and the bubble absorption heights (BAHs) were measured when the two kinds of different structure nozzles (single-orifice or multi-orifice nozzle…

    Get Price
  • NOZZLE TESTS FOR SIMULATING HEAVY RAIN IN A

    2011-5-14 · AFwAtL-TR-93-31 31 NOZZLE TESTS FOR SIMULATING HEAVY RAIN IN A WIND TUNNEL-.7ames K. LuersIra B. Fiscus University of Dayton 'a* Research Institute Dayton, Ohio 45469 Ott January 1984 Final 'Report for Period February 1983 to February 1984

    Get Price
  • (PDF) Sensitivity Analysis of Fuel Injection ...

    2019-1-30 · Figure 6c showed the variation of the injection rate and nozzle exit velocity with the injection pressure during the steady state period. The mass fl ow rate of the nozzle and the jet velocity at the

    Get Price